Thermocouple : K, J, E, T, R, B, S, L, N, U, WRe 5-26, PL-Ⅱ (Refer to input signal and measurement range)

RTD : Pt 100 Ω, KSPt 100 Ω

DC voltage input : 1 - 5 V d.c., 0 - 10 V d.c., -10 ~ 20 mV d.c., 0 - 100 mV d.c. (Free scale method)

⚠️ Notice

When using a current input, this product functions properly only with voltage divider feedback.

Therefore, be sure to check whether the circuit uses current-sensing feedback or voltage divider feedback before use.

However, if only one channel is used, both feedback methods are supported.

250 ms

Basically below the decimal point of "Measurement range index"

Thermocouple and DC voltage input (mV) : 1 MΩ min.,DC voltage input(V): approx. 1 MΩ

Thermocouple : 250 Ω max., voltage : 2 kΩ max

- RTD : 10 Ω max./wire (conductor resistance among 3 wires should be the same)

- Within ±10 V (thermocouple, RTD, voltage: mV d.c.)

- Within ±20 V (voltage: V d.c.)

- NMRR (normal mode) : 40 dB min. (50/60 Hz ±1%)

- CMRR (common mode) : 120 dB min. (50/60 Hz ±1%)

- Thermocouple/RTD (KS/IEC/DIN)

±1.5 ℃ (15 ~ 35 ℃), ±2.0 ℃ (0 ~ 50 ℃)

- Thermocouple : OFF, UP/DOWN scale selectable

- RTD: UP Scale (detection current during thermocouple and RTD BURN- OUT: approx. 50 mA)

Display and record accuracy: ±0.5% (Full Scale)

Refer to “Input signal and measurement range”. Thermocouple and RTD can be changed within the

range of input signal and measurement range chart. DC voltage can change the minimum voltage and

maximum voltage within each range. Scaling possible within the conditions of measurement range.

- Contact capacity : 240 V a.c. 1 A, 30 V d.c. 1 A (resistive load)

- Contact configuration : 1a

- Output contacts: 2 (AL1, AL2)

- Contact capacity : 240 V a.c. 3 A, 30 V d.c. 3 A (resistive load), contact configuration : 1C

- Output operation : PID, ON/OFF, proportional cycle : 1 ~ 1,000 sec.

- Output limit : 0.0~100.0% range high limit (OH), low limit (OL) selectable,also during auto-tuning.

- ON/OFF hysteresis : 0 ~ 100% (Full Scale)

- Time resolution : lower between 0.1% or 10 ms

- ON voltage : approx. 12 V d.c. min.

(load resistance 400 Ω, approx. 30 mA current limit during short circuit)

- OFF voltage : 0.1 V d.c. max., proportional cycle : 1 ~ 1,000 sec.

- Output operation : PID

- Output limit : 0.0~100.0% range high limit (OH),low limit (OL) selectable,also during auto-tuning.

- Time resolution : lower between 0.1% or 10 ms.

- Load resistance: 400 Ω max.

- Accuracy : ±0.5% of max. scale (4 - 20 mA range), resolution : approx. 3,000

- Output ripple : max. ±0.3% (P-P) of max. scale (150 Hz)

- Output sampling cycle : 250 ms, output operation: continuous PID

- Output limit: -5.0~105.0% range high limit (OH),low limit (OL) selectable,also during auto-tuning

- Input calibration (Bias) : -100.0 ~ 100.0 % for instrument range

(can calibrate the desired correction value to the measurement input value)

- Scaling: measurement range scaling is possible according to maximum value (SH) and

minimum value (SL) settings of measurement range.

- Input filter: OFF, 1 ~ 120 sec.

PID groups : 3 types

- PID groups : 3 types

- Auto-tuning : auto-tuning operates according to set value (SV) (standard type, low PV type)

- Proportional band : 0.1 ~ 999.9% (max. range)

- Integral time : OFF, 1 ~ 6000 sec.

- Derivative time : OFF, 1 ~ 6000 sec.

- ON/OFF control : by selecting output code (OT) “1”

- PID selection : ZONE PID / Auto 1, 2, 3 selectable.

- Manual reset : -5.0 ~ 105.0% of output (valid only when integral time is “OFF”)

- Direct /reverse action selection: selectable by parameter.

- Emergency output value : -5.0 ~ 105.0% of output value

- ON/OFF hysteresis (HYS) : 0.0~100.0% of instrument range (however, valid only if set to ON/OFF control)

- ARW (Anti Reset Wind-up) : AUTO, 50.0 ~ 200.0%

- Fuzzy function: ON or OFF selection by parameter

- Ramp function: the rising temperature and falling temperature gradient can be set in hours or

minutes when the power is on.

- Set contacts : 2 (1 contact per channel, 1-channel type only supports alarm 1 contact)

- Alarm types : high/low, high/low deviation, hold high/low, heater break (refer to "alarm type and code" table)

- Setting range : during absolute value alarm 0 ~ 100% of instrument range

during deviation alarm -100 ~ 100% of instrument range

- Measuring points: 1

- Response time : according to record speed

- Record type : thermal line

- Printing method : 203 dpi (8.0 dots/mm) 384 dots per line

- Recording speed : 20, 30, 60, 120, 180, 300, 600, 900 mm/h

- Recorder paper check: if there is no paper the front display window P-END lamp turns on and record stops.

- Recorder paper : width 57.5 mm, length approx. 16 m

- Continuous vibration (5 - 14 Hz) : Forward width 1.2 mm. max.,

- Continuous vibration (4 ~ 150 Hz): 4.9 m/s² max.

- Chort-time vibration : 14.7 m/s² , 15 sec. max. (each of 3 directions)

- Shock: 147 m/s², 11 ms max. (6 directions each 3 times)

- Panel dimensions: refer to "dimension and panel cutout"

- Ambient temperature : 0 ~ 50 ℃

- Ambient humidity : 35 ~ 85 %RH (with no condensation)

- Magnetic influence : 400 AT/m max.

- Warm-up time : 30 minutes min.

- Thermocouple, voltage input : ±1 μV/℃ or ±0.01%/℃ of max. range

- RTD input : ±0.05 Ω/℃ max.

- Analog output : Max. ±0.05%/℃ of max. range (continuous output)

100 - 240 V a.c. (voltage fluctuation rate ±10% )

50 - 60 Hz

15 W max., 20 VA max.

Between primary terminal and secondary terminal:

500 V d.c. 20 MΩ min.

Between primary terminal and ground:

500 V d.c. 20 MΩ min.

Between secondary terminal and ground:

500 V d.c. 20 MΩ min.

Between primary terminal and secondary terminal:

2,300 V a.c. 50/60 Hz for 1 minute

Between primary terminal and ground:

2,300 V a.c. 50/60 Hz for 1 minute

Between secondary terminal and F•G:

1,500 V a.c. 50/60 Hz for 1 minute

-25 ~ 70℃

5 ~ 95% RH (with no condensation)

1 m max. in packed condition (natural fall)

EIA RS485

max. 31

(1 ~ 99 address settings available)

2-wire half-duplex

Asynchronous

None

Within 1.2 km

2400(setting value 2), 4800(setting value 3),

9600(setting value 4), 14400(setting value 5),

19200(setting value 6)

(communication speed changes by parameter settings)

1 BIT

7 or 8 BIT

None, Even Numbers, Odd numbers

1 or 2 BIT

PC LINK(setting value 0),

PC LINK SUM(setting value 1),

MODBUS-ASCIl(setting value 2),

MODBUS-RTU(setting value 3)

Reception handling time + (response time × 10 ms)